SPARS
September 1, 2014 Unpacking wing kit
September 7, 2014 Countersunk #40 holes
September 8, 2014 Countersunk #30 holes
September 9, 2014 Started installing nut plates in spars
September 20, 2014 Finished installing fuel tank nut plates
September 21, 2014 Installed access panel nut plates
September 27, 2014 Started drilling the rear spar parts
September 28, 2014 Drilled spacers for tie-down bar
September 30, 2014 Cut spar doublers
October 4, 2014 Rear spar work
October 5, 2014 Finished left rear spar, started right rear spar
October 8, 2014 Drilled the tie-down bar and spacer
October 13, 2014 Finished assembly of the right rear spar
WINGS
October 18, 2014 Deburred ribs
October 20, 2014 Finished deburring ribs, preparing left ribs
October 21, 2014 Clecoed ribs to main and aft spars
October 25, 2014 Primed ribs, purchased wing stand lumber
October 26, 2014 Riveted ribs to main spar
November 2, 2014 Riveted ribs to aft spar
November 8, 2014 Worked on wing stand
November 16, 2014 Added wing support beams to wing stand
November 30, 2014 Drilled wire-routing holes in ribs, started fluting ribs
December 6, 2014 Preped the right wing ribs
December 7, 2014 Primed right wing ribs
December 20, 2014 Riveted right wing ribs to main spar
December 21, 2014 Riveted the right wing ribs to the rear spar
January 1, 2015 Installed right wing supports to the wing stand
February 15, 2015 Cleccoed the top skins to the wing, finished left portion of wing stand
February 16, 2015 Match drilled right wing walk doubler, clecoed skins to skeleton
February 21, 2015
February 28, 2015
March 7, 2015
March 14, 2015
March 21, 2015 Right wing bottom skin
March 23, 2015 Right wing outboard LE
June 6, 2015 Wing stand
July 11, 2015 Right leading edge assembly
July 18, 2015 Right leading leading edge rework
July 19, 2015 Right leading edge joiner work
July 25, 2015 Primed right leading edge
July 26, 2015 Riveted right leading edge
February 13, 2016 Riveted nut plates to right joiner plate
February 15, 2016 Dimpled/drilled left joiner plate
February 16, 2016 Dimpled left leading edge ribs
February 17, 2016 Dimpled remaining left leading edge ribs
February 21, 2016 Dimpled left leading edge skin
February 29, 2016 Left leading edge deburring, priming, and riveting
March 3, 2016 Continued riveting left leading edge
March 5, 2016 Finished riveting left leading edge, dimpled right outboard skin
March 6, 2016 Dimpled right inboard top skin, dimpled rights ribs
March 24, 2016 Deburred and dimpled left inboard skin
March 26, 2016 Deburred and dimpled wing walk skin, dimpled left wing ribs
April 16, 2016 Started installing right leading edge to spar
April 18, 2016 Finished installing blind rivets in right spar
April 19, 2016 Riveted right leading edge to spar
April 23, 2016 Misc right wing work
April 25, 2016 Dimpled rear spar
April 29, 2016 Cleccoed right top skins, countersunk left spar
May 15, 2016 Started riveting right top skins to skeleton
May 17, 2016 Continued riveting right top skins
May 22, 2016 Almost done riveting right top skins
May 24, 2016 Continued setting remaining right top skins rivets
May 27, 2016 Deburred and primed left top skins
May 31, 2016 Assembled the stall warning mechanism
June 1, 2016 Cut the aileron pushrods
June 2, 2016 Installed stall warning in LE
June 4, 2016 Riveted left LE to spar
June 5, 2016 Installed left fuel tank on wing
June 7, 2016 Drilled pushrod end caps for tube #1
June 9, 2016 Drilled pushrod end caps for tube #2
June 14, 2016 Dimpled trailing edge of left wing
June 16, 2016 Clecoed left wing skins to skeleton
June 18, 2016 Stated riveting top skins on left wing
June 20, 2016 Riveted trailing edge of left wing
Jun 23, 2016 Built wing holding fixture
June 25, 2016 Riveted left top wing skins
June 26, 2016 Misc wing wrap-up work
June 28, 2016 Started working on aileron brackets
June 29, 2016 Moved wing to holder
July 6, 2016 Disassembled wing stand, started aileron brackets
July 7, 2016 Riveted right aileron brackets together
July 8, 2016 Riveted right aileron brackets to wing
July 10, 2016 Riveted right rear spar service bulletin, riveted right aileron fairing
July 12, 2016 Dimpled inboard bottom right skin
July 14, 2016 Dimple right bottom outboard skin and ribs
July 16, 2016 Primed right bottom skin and pushrods, riveted right flap brace
July 19, 2016 Riveted right bottom skin nut plates
July 24, 2016 Started riveting right inboard bottom skin
July 26, 2016 Riveted right bottom inboard skin
August 2, 2016 Continued riveting right bottom inboard skin
August 7, 2016 Continued riveting right bottom inboard skin
August 15, 2016 Riveted nut plates to right outboard bottom skin
August 20, 2016 Began riveting right bottom outboard skin
August 23, 2016 Started riveting lleft wing aileron brackets
August 27, 2016 Continued riveting left aileron brackets, primed flap and aileron braces.
September 4, 2016 Right leading edge repair, installed left inboard aileron bracket
September 5, 2016 Left flap brace, push rod assembly
September 14, 2016 Left aileron brace, started pitot tube work
October 8, 2016 Continued riveting bottom right wing skin
October 15, 2016 Finish Right Wing!
September 30, 2018 Started removing outer bottom skin from right wing
FUEL TANKS
April 25, 2015 Z-brackets
April 26, 2015 More Z-brackets
May 9, 2015 Z-bracket rework
May 10, 2015 More Z-bracket rework
May 17, 2015 Fuel Tank Stiffeners
May 30, 2015 Left fuel tank ribs
May 31, 2015 Cleccoed left tank to wing
June 13, 2015 Z-brackets, 3rd attempt
June 14, 2015 Left fuel tank skin/baffle
June 21, 2015 Right fuel tank stiffeners and ribs
July 4, 2015 Right wing Z-brackets
July 5, 2015 Right wing fuel tank ribs/skin
October 1, 2015 Left tank skin drilling
October 4, 2015 Left tank more drilling, cut rib access hole
October 5, 2015 Left tank attach bracket
October 6, 2015 Cut right angle bracket
October 8, 2015 Match drilled left angle bracket, drilled left vent hole
October 9, 2015 Match drilled left tank rib
October 12, 2015 Riveted left tank rib stiffener, match drilled left fuel cap
October 31, 2015 Drilled the fuel drain
November 1, 2015 Deburred and dimpled left tanks skin/ribs
November 3, 2015 Misc left tank deburring
November 4, 2015 Match drilled right tank
November 7, 2015 Misc right tank drilling, finished right angle bracket
November 8, 2015 Drilled right fuel cap and drain
November 9, 2015 Cut access hole in right fuel tank
November 18, 2015 Match drilled right doubler ring holes
November 21, 2015 Riveted nut plates to right inboard rib, dimpled ribs/stiffeners
November 28, 2015 Deburred and dimpled right fuel tank skin
December 3, 2015 Installed left tanks stiffeners
December 5, 2015 Installed right tank stiffeners, fuel drains
December 6, 2015 Right fuel cap installation
December 7, 2015 Repaired leading edge fixture
December 8, 2015 Installed 1 rib on right tank
December 12, 2015 Installed 4 ribs on right tank
December 19, 2015 Installed 1 rib on left tank
December 28, 2015 Installed 2 ribs on left tank
December 30, 2015 Installed 2 ribs on left tank
January 2, 2016 Installed 1 rib on left tank
January 5, 2016 Installed outboard rib on right tank
January 9, 2016 Installed inboard rib on right tank
January 10, 2016 Installed right tank fuel pickup tube and fuel sensor
January 16, 2016 Sealed rivet shop heads on right tank
January 19, 2016 Riveted right tank angle bracket
January 23, 2016 Misc right tank assembly, assembled access plate, installed vent line
February 8, 2016 Installed baffle to right tank
February 9, 2016 Finished right baffle installation
February 13, 2016 Installed access plate and fuel sender to right tank
March 20, 2016 Leak check right tank
March 26, 2016 Installed inboard left tank rib, sealed leaks on right tank
April 4, 2016 Installed lock wire on left fuel tube
April 12, 2016 Leak checked right tank, drilled OAT hole
May 1, 2016 Drilled left fuel sender, installed vent tube
May 4, 2016 Cleccoed left tank baffle, riveted Z-brackets
May 5, 2016 Riveted bottom skin-to-baffle rivets
May 8, 2016 Riveted top skin-to-baffle rivets
May 11, 2016 Installed fuel level sensor and access cover
May 24, 2016 Leak checked left fuel tank
May 26, 2016 Sealed left fuel tank leak
June 2, 2016 FINISHED FUEL TANKS
AILERONS
January 2, 2015
January 3, 2015 **Needs work**
January 10, 2015 Aileron stiffeners and skin
January 11, 2015
January 16, 2015 Cut aileron doublers
January 17, 2015 Primed aileron skin/stiffeners
January 18, 2015 Aileron doubler
January 20, 2015 Ailerons spar work
January 24, 2015 Drilled right aileron, folded trailing edge
January 25, 2015 Dimpled right aileron skin
January 31, 2015 Countersunk right aileron counterweight, primed right aileron
February 7, 2015 Riveted right nose skin and spar
February 8, 2015 Riveted right aileron top skin
February 13, 2015 not complete
March 29, 2015 Started working on the left aileron
March 30, 2015 Continued working on the left aileron
April 11, 2015 Left aileron LE **needs pic updates**
April 12, 2015 More aileron work
April 18, 2015 Finished up left aileron
FLAPS
August 1, 2015 Match drilled skeletons
August 2, 2015 Left flap hinge drilling
August 15, 2015 Cut flap angle aluminum, drilled left flap top skin
August 19, 2015 Countersunk bottom flap skin
August 20, 2015 Drilled/dimpled left flap parts
August 21, 2015 Primed left flap parts, drilled right flap parts
August 22, 2015 Deburred/dimpled right flap parts
August 23, 2015 Drilled right flap brackets
August 26, 2015 Deburred and dimpled right flap parts
August 29, 2015 Started riveting left flap
August 30, 2015 Continued riveting left flap
September 1, 2015 Discovered a big mistake in the flap skin
September 12, 2015 Primed right flap
September 13, 2015 Started riveting right flap
September 14, 2015 Finished riveting ribs to right skin
September 18, 2015 Prepped piano hinge, started riveting top skin to spar
September 19, 2015 Riveted top skin to spar
September 27, 2015
July 19, 2020
July 24, 2020
August 23, 2021
August 24, 2021
August 26, 2021
August 29, 2021
August 30, 2021